Відео

I’m glad you had to change the connector so we could see it replaced but I would have waited until after I tested the light and then shrunk it, but I guess you have confidence in your work.

Thank you saved me a lot of headache

This is lies, the easyout you linked to doesnt fit in any type of traditional socket. It's squared not a hexagon. Why would you have people buy that through your link when its clearly not the tool you are using in the video?

OMG I am a dollar tree junkie and this is cute and functional

my car battery went dead while bleeding my brakes. After i finished the brake flush, i jumped the engine but then immediately the check engine light turned on. I went to autozone and code ABS malfunction and traction off showed up on dash. Not knowing what to do, i removed from the battery then reconnect, check engine light turned off for now but for how long? car is fairly new

Dumb question, what happens if the ceramic goes into the cylinder head. What can you do to clean it? (Without having to disassemble the whole block)?

I have a realistic lab 65, same thing It won't turn on, I can manually spin the platter so it's not sized. I see a few caps etc under the plastic cover on the underside, that the only electronics? Must be something there u think?

It annoys the crap out of me that I can’t turn these ugly amber lights off while driving. Sorry if people like them, I personally don’t.

I can spin my wash plate by hand, when my machine goes into spin cycle its makes a bad sound and dosent spin or agitate, this goes for all modes is this my issue?

Try no to get bolt off but feels like the whole thing under is spinning with it??

I have a drimel that has them and what's weird is, if you put 1 in 1 side or swap them it doesn't work... I was looking up for an air impact and saw this.

My twin mattress was way harder on every step. Breaking down the spring part is definitely the hardest part.

It worked after the fact, had to get an old cheap 14 mm, and a long 3/8 extension, tapped it right on, lowered the spare no problm. Gonna drill a hole in the 14 mm while it is in the " lock mechanism, put a roll pin in , and just leave it on, and an old 3/8 ratchet, and long 3/8" extension with the tire tools/ jack.

I recently picked up a similar trimmer. Does this one have a brake on the head?

My Karcher pressure washer with Tecumseh engine started with 3 pushes on the primer bulb. First pull. Ran it for 5 minutes and shut it off. No way to start it 5 minutes later. New spark plug. Seems it has a starting problem when the engine is hot.

Did you have to adjust the converter?

Wow. This video is so useful. Thanks so much 🙌🏽

thanks so much for the video! what a stupid design!

Bought one. I think it'll work great for me. This will require practically no skill while swinging an axe does. Much safer for young scouts too.

Thank you, now I can rip the ivory keys out of my 80 year old antique piano. 😊

I have to fix mine too but I don't know how

Thank you 🙏

Thanks so much for posting this I was about to return my lights for the sme eason and after I watched this video I went outside and cranked them tigher and it worked! You never know who your videos will help!

Great video! Love how you stressed how the colors don't matter and only the pin location. So many (self included) get tripped up by following color codes. Especially with more than one wiring standard. I saw how one guy used a label maker and marked each terminal with the corresponding function on the trailer so that, in a pinch, you can quickly see where that wire goes on the trailer while wiring it up or converting to a different wiring standard if the need ever arises. Every trailer I've owned over 60 years has come from the manufacturer with garbage wiring. Those scotch connectors should be illegal! But I digress. lol What was your reason for mounting the box on the outside of the frame where it is so much more susceptible to being damaged. Was it just for the ease of installation and convenience? Or was there another reason? I always mount mine inside the frame or under the bed to get the box out of the way of everything. It's not nearly as convenient as your choice but I just know that shortly after I mounted mine there, I'd want to install a WDH or something and my box would be in the way or somehow get damaged - lol.

Thank you

Hello, can the washplate on this washer be change and be replace with a agitator instead??

This is by far the best video illustrating the simple 123 method to change an oil filter on an oil burner, bravo, and thank you.😊

how do you replace the top? I have the glue and a clamp for the head, but no idea how to position them

Me gustaria tener el moldecito o las medidas porfis

This is great. I've been looking to get one of these for the past few years from aliexpress to tether my phone to my gamecube to play it online as its a fully portable console

Perfect Instructions, Thank You.

Nice shelf Ron.

I need help with mine. I replaced the control board but it’s still not agitating

Neato! I'm going to put all my fittings in a bucket until I have $50 worth and then I'll buy this tool!

Thanks!

Thanks for the video. I have the same type of windows and wanted to tint my windows. Now I know I can. So cool.

Thanks for the help! Job done.

What song are you listening to lol it sounds awesome

Just cut mine apart. Gonna take out top also..must line up actuator ..spray lube on all moving parts

Wth. The vent door gasket goes bad have to cut out a windows to get to door clean off old sticky gasket. Cover with hvac tape .no more stuck door focus is bad for this

Can I manually adjust the temperature control?

Thanks, Ron!

I believe its not a bad power tool kit for the price i like dewalt but its more pricey i just ordered this kit from ace hardware here in town. I paid $295.23 after tax, free shipping an it was $100 off regular sell price. Normally $369.99 at ace nice set 👌 i like that this set comes with the grinder

Thanks for share ❤❤❤❤❤

Well, it looks like this is my next project. I have the Maytag Bravos top loader, and I'm guessing this is the little problem. Before I get started, I wanted to know if anyone has used the upgraded metal hub replacement from amazon? I don't want to have to make this replacement again. Please advise me if i should just use the plastic replacement or the metal one. Thank you!

Thank you!

Outer lamp easy, what about the one ducked inside...

I have a Blackmagic ATEM Pro which requires wired internet. This looks like it would work, but I need to connect Hotel WiFi, and thus change the settings for every hotel. Plus hotel systems generally have security above the router layer, where a browser pops up asking for your name and room number. How would I reconfigure for each stay? Can it handle a password after WiFi connects?

Great review, literally best vid I’ve ever watched, good thing your him

Thanks! I got them in and it worked. The resister was pretty easy. The hardest part was putting the new blower back in...the screw holes were too tight to hand start the screws. Holding the blower up with one hand and ratcheting the screws in with the other was tough...ended up having my son hold the blower up while I put in the screws.